DAVEGA X, assembled

4,190 

Baseplate not included!

Available baseplate options:

Clear
Category:

Description

Pre-assembled and ready to use. Just plug it in.

DAVEGA X is an advanced on-board telemetry device for VESC® based speed controllers. It comes in an aluminum enclosure with several color options to choose from.

Please see the product site for detailed information.

Package contents

  • pre-assembled DAVEGA X v1.2
  • flexible ribbon cable
  • JST-PH housings: 7P (2pcs), 8P (2pcs)
  • screen protectors: glass (pre-installed), 2pcs acrylic (spares)
  • double sided rubber tape (for replacing the screen protector)
  • M3x6mm bolts: stainless steel (5pcs), blued steel (5pcs)

Note that the baseplate is no longer included and has to be ordered separately.

What cable length do I need?

For exact measurement, take a string and route it from the center-point of the front truck mounting holes to your ESC UART port. Then add 10 cm to the length.

A good quick estimate for 2WD setups with a bottom mounted enclosure is to measure the distance between the deck nose and the rear of the enclosure.

The 100 cm cable is long enough for most setups.

7P or 8P connector?

Find the communication port on your speed controller. The pins should be labeled as follows:

  • 5V
  • 3.3V or VCC
  • GND
  • ADC1
  • RX or TX
  • TX or RX
  • ADC2
  • ADC3 (missing on 7P ports)

The communication port on most VESC® based controllers either has 7 or 8 pins (there’s an extra ADC3 pin in the latter case). Should your communication port have a different number of pins or should the pins be organized in a different order than on the list above please let us know in the order notes and we will do our best to set up your cable as appropriate. Note that DAVEGA X is tolerant to swapping RX/TX starting from firmware v4.04 (guaranteed on all new units).

We also highly recommend that you watch this video where we discuss the cable setup in more detail.

Software features

Telemetry
  • speed
  • distance traveled
  • battery state of charge
  • projected range
  • average power consumption
  • motor/battery current
  • energy discharged/re-generated
  • motor temperature
  • VESC fault codes
BMS data (with ENNOID-BMS, DieBieMS, FlexiBMS, or LLT Power BMS)
  • individual cell voltages
  • charge current
  • state of charge
  • balancing details
  • note: LLT Power BMS support is currently experimental
Other features
  • session and lifetime stats
  • parts lifespan tracking
  • over-the-air firmware updates
  • automated data backup to cloud

Hardware

  • 2.8″ 240×320 TFT display
  • ESP32, 512 kB RAM, 4 MB flash
  • 802.11 b/g/n 2.4 GHz Wi-Fi
  • BT, BLE

VESC® compatibility

DAVEGA X works with all VESC® based controllers running the firmware v3.48 or later.

This includes but is not limited to the following:

Water resistance

The enclosure does not leak around the screen protector or the buttons. While we do not recommend purposely using the DAVEGA X in rain conditions, if you get caught in the rain, continuing to ride for a few minutes to reach the nearest dry place is OK. After any exposure to a heavy rain, we recommend that you detach the DAVEGA housing from the board while you are letting the board dry.

Made in the Czech Republic

Most of the DAVEGA X parts, including the aluminum enclosure, cables, and glass screen protectors, are manufactured in the Czech Republic.

The electronics are hand-soldered and well tested in-house.

Demo

Additional information

Weight 0.208 kg
Dimensions 9.8 × 6.2 × 2.2 cm

Reviews

There are no reviews yet.

Be the first to review “DAVEGA X, assembled”

Your email address will not be published. Required fields are marked *